API 5L PSL2 Pipes in Oman
Pipes are prime units of operation in hydrocarbon, petroleum, natural gas and other industries. They are the backbone of these industries and any weakness in the backbone can lead to operational troubles. This is the reason businesses place a huge emphasis on buying quality pipes and tubes. They always go for trusted and standard API 5L PSL2 Pipes and as a measure of quality, they look up to API (American Petroleum Institute) specifications. API 5L specification pipes are known to be strong and sturdy and they cover seamless and welded steel line pipes from grade X42 to X80. The API 5L PSL2 Pipes are known to be fit for the transmission of oil, water, and gas.
Coming to API 5L PSL2 pipes, these pipes conform to the product specification level (PSL)2 of the American Petroleum Institute. So, what does PSL2 mean? PSL2 defines the chemical, mechanical properties, manufacturing, inspection, defect repair, certification and traceability standards of these line pipes. These API 5L PSL2 Pipes adhere to the said standards and therefore, come with the hallmark of trust and guarantee. The API has established two product specification levels- PSL1 and PSL2 for the steel line pipes and PSL2 pipes are relatively higher quality pipes than PSL1 and at Rexal Tubes, we offer a wide range of API 5L PSL2 pipes that can meet the demands of different industries.
API 5L Gr B PSL2 Pipe in Oman
Applicable codes and standards API 5L, 45th Edition / ISO 3183 Specification for line pipe – technical delivery conditions.
Size: ¼” to 36”
Wall Thickness: SCH 10 to 160, STD, XS, XXS
Length: up to 12 Meters
*Additional testing requirements met*: NACE MR
0175,NACE TM0177,NACE TM0284,HIC TEST, SSC TEST, H2 SERVICE,IBR, ECT in all
the products.
CHEMICAL COMPOSITION | ||||||||||
C | Si | MN | P | S | V | Nb | Ti | Other | Carbon Equivalent | |
Max (b) | Max | Max (b) | Max | Max | Max | Max | Max | % maximum | ||
CE(IIW) | CE(Pcm) | |||||||||
0.22 | 0.45 | 1.20 | 0.025 | 0.015 | 0.05 | 0.05 | 0.04 | (g) | 0.43 | 0.25 |
MECHANICAL REQUIREMENT | ||||||||
Tensile Requirements on Pipe body of welded pipes | Ratio | Elongation | CVN Absorbed Energy | Heat Treatment | ||||
Yield Strength (R10.5) | Tensile Strength (R) | R 10.5/ R | % | 0 degree celsius | ||||
PSI | Mpa | PSI | Mpa | Max | Minimum | Min J | Min ft. lb | Wield Seam Normalizing |
35,500-65,300 min | 245-450 min | 60,200-110,200 min | 415-760 min | 0.93 | – | – | ||
IMPACT TEST | |
AVG ABSORBED ENERGY | IND. ABSORBED ENERGY |
MIN (JOULES) | MIN (JOULES) |
27 | 20 |
API 5L X42 PSL2 Pipe in Oman
Applicable codes and standards API 5L, 45th Edition / ISO 3183 Specification for line pipe – technical delivery conditions.
Size: ¼” to 36”
Wall Thickness: SCH 10 to 160, STD, XS, XXS
Length: up to 12 Meters
*Additional testing requirements met*: NACE MR
0175,NACE TM0177,NACE TM0284,HIC TEST, SSC TEST, H2 SERVICE,IBR, ECT in all
the products.
CHEMICAL COMPOSITION | ||||||||||
C | Si | MN | P | S | V | Nb | Ti | Other | Carbon Equivalent | |
Max (b) | Max | Max (b) | Max | Max | Max | Max | Max | % maximum | ||
CE(IIW) | CE(Pcm) | |||||||||
0.22 | 0.45 | 1.30/ | 0.025 | 0.015 | 0.05 | 0.05 | 0.04 | (g) | 0.43 | 0.25 |
MECHANICAL REQUIREMENT | ||||||||
Tensile Requirements on Pipe body of welded pipes | Ratio | Elongation | CVN Absorbed Energy | Heat Treatment | ||||
Yield Strength (R10.5) | Tensile Strength (R) | R 10.5/ R | % | 0 degree celsius | ||||
PSI | Mpa | PSI | Mpa | Max | Minimum | Min J | Min ft. lb | Wield Seam Normalizing |
42,100-71,800 min | 290- 495 min | 60,200- 110,200 min | 415- 760 min | 0.93 | – | – | ||
IMPACT TEST | |
AVG ABSORBED ENERGY | IND. ABSORBED ENERGY |
MIN (JOULES) | MIN (JOULES) |
27 | 20 |
API 5L X46 PSL2 Pipe in Oman
Applicable codes and standards API 5L, 45th Edition / ISO 3183 Specification for line pipe – technical delivery conditions.
Size: ¼” to 36”
Wall Thickness: SCH 10 to 160, STD, XS, XXS
Length: up to 12 Meters
*Additional testing requirements met*: NACE MR
0175,NACE TM0177,NACE TM0284,HIC TEST, SSC TEST, H2 SERVICE,IBR, ECT in all
the products.
CHEMICAL COMPOSITION | ||||||||||
C | Si | MN | P | S | V | Nb | Ti | Other | Carbon Equivalent | |
Max (b) | Max | Max (b) | Max | Max | Max | Max | Max | % maximum | ||
CE(IIW) | CE(Pcm) | |||||||||
0.22 | 0.45 | 1.30/ | 0.025 | 0.015 | 0.05 | 0.05 | 0.04 | (g) | 0.043 | 0.025 |
MECHANICAL REQUIREMENT | ||||||||
Tensile Requirements on Pipe body of welded pipes | Ratio | Elongation | CVN Absorbed Energy | Heat Treatment | ||||
Yield Strength (R10.5) | Tensile Strength (R) | R 10.5/ R | % | 0 degree celsius | ||||
PSI | Mpa | PSI | Mpa | Max | Minimum | Min J | Min ft. lb | Wield Seam Normalizing |
46,400-76,100 min | 320-525 min | 63,100-110,200 min | 435- 760 min | 0.93 | – | – | ||
IMPACT TEST | |
AVG ABSORBED ENERGY | IND. ABSORBED ENERGY |
MIN (JOULES) | MIN (JOULES) |
27 | 20 |
API 5L X52 PSL2 Pipe in Oman
Applicable codes and standards API 5L, 45th Edition / ISO 3183 Specification for line pipe – technical delivery conditions.
Size: ¼” to 36”
Wall Thickness: SCH 10 to 160, STD, XS, XXS
Length: up to 12 Meters
*Additional testing requirements met*: NACE MR
0175,NACE TM0177,NACE TM0284,HIC TEST, SSC TEST, H2 SERVICE,IBR, ECT in all
the products.
CHEMICAL COMPOSITION | ||||||||||
C | Si | MN | P | S | V | Nb | Ti | Other | Carbon Equivalent | |
Max (b) | Max | Max (b) | Max | Max | Max | Max | Max | % maximum | ||
CE(IIW) | CE(Pcm) | |||||||||
0.22 | 0.045 | 1.40/ | 0.025 | 0.015 | (d) | (d) | (d) | (g) | 0.43 | 0.25 |
MECHANICAL REQUIREMENT | ||||||||
Tensile Requirements on Pipe body of welded pipes | Ratio | Elongation | CVN Absorbed Energy | Heat Treatment | ||||
Yield Strength (R10.5) | Tensile Strength (R) | R 10.5/ R | % | 0 degree celsius | ||||
PSI | Mpa | PSI | Mpa | Max | Minimum | Min J | Min ft. lb | Wield Seam Normalizing |
52,200-76,900 min | 360-530 min | 66,700-110,200 min | 460-760 min | 0.93 | – | – | ||
IMPACT TEST | |
AVG ABSORBED ENERGY | IND. ABSORBED ENERGY |
MIN (JOULES) | MIN (JOULES) |
27 | 20 |
API 5L X56 PSL2 Pipe in Oman
Applicable codes and standards API 5L, 45th Edition / ISO 3183 Specification for line pipe – technical delivery conditions.
Size: ¼” to 36”
Wall Thickness: 6 MM to 65MM
Length: up to 18 Meters
*Additional testing requirements met*: NACE MR
0175,NACE TM0177,NACE TM0284,HIC TEST, SSC TEST, H2 SERVICE,IBR, ECT in all
the products.
CHEMICAL COMPOSITION | ||||||||||
C | Si | MN | P | S | V | Nb | Ti | Other | Carbon Equivalent | |
Max (b) | Max | Max (b) | Max | Max | Max | Max | Max | % maximum | ||
CE(IIW) | CE(Pcm) | |||||||||
0.26 | – | 1.20 | 0.030 | 0.030 | (c),(d) | (c),(d) | (d) | (a) | – | – |
MECHANICAL REQUIREMENT | ||||||||
Tensile Requirements on Pipe body of welded pipes | Ratio | Elongation | CVN Absorbed Energy | Heat Treatment | ||||
Yield Strength (R10.5) | Tensile Strength (R) | R 10.5/ R | % | 0 degree celsius | ||||
PSI | Mpa | PSI | Mpa | Max | Minimum | Min J | Min ft. lb | Wield Seam Normalizing |
35,500 min | 245 min | 60,200 min | 415 min | – | – | – |
API 5L X60 PSL2 Pipe in Oman
Applicable codes and standards API 5L, 45th Edition / ISO 3183 Specification for line pipe – technical delivery conditions.
Size: ¼” to 36”
Wall Thickness: SCH 10 to 160, STD, XS, XXS
Length: up to 12 Meters
*Additional testing requirements met*: NACE MR
0175,NACE TM0177,NACE TM0284,HIC TEST, SSC TEST, H2 SERVICE,IBR, ECT in all
the products.
CHEMICAL COMPOSITION | ||||||||||
C | Si | MN | P | S | V | Nb | Ti | Other | Carbon Equivalent | |
Max (b) | Max | Max (b) | Max | Max | Max | Max | Max | % maximum | ||
CE(IIW) | CE(Pcm) | |||||||||
0.12 (e) | 0.45 (e) | 1.60 (e) | 0.025 | 0.015 | (h) | (h) | (h) | (i) | 0.43 | 0.25 |
MECHANICAL REQUIREMENT | ||||||||
Tensile Requirements on Pipe body of welded pipes | Ratio | Elongation | CVN Absorbed Energy | Heat Treatment | ||||
Yield Strength (R10.5) | Tensile Strength (R) | R 10.5/ R | % | 0 degree celsius | ||||
PSI | Mpa | PSI | Mpa | Max | Minimum | Min J | Min ft. lb | Wield Seam Normalizing |
60,200-81,900 min | 415-565 min | 75,400-110,200 min | 520-760 min | 0.93 | 27 | 20 | ||
IMPACT TEST | |
AVG ABSORBED ENERGY | IND. ABSORBED ENERGY |
MIN (JOULES) | MIN (JOULES) |
27 | 20 |
API 5L X65 PSL2 Pipe in Oman
Applicable codes and standards API 5L, 45th Edition / ISO 3183 Specification for line pipe – technical delivery conditions.
Size: ¼” to 36”
Wall Thickness: SCH 10 to 160, STD, XS, XXS
Length: up to 12 Meters
*Additional testing requirements met*: NACE MR
0175,NACE TM0177,NACE TM0284,HIC TEST, SSC TEST, H2 SERVICE,IBR, ECT in all
the products.
CHEMICAL COMPOSITION | ||||||||||
C | Si | MN | P | S | V | Nb | Ti | Other | Carbon Equivalent | |
Max (b) | Max | Max (b) | Max | Max | Max | Max | Max | % maximum | ||
CE(IIW) | CE(Pcm) | |||||||||
0.12 (e) | 0.45 (e) | 0.60 (e) | 0.025 | 0.015 | (h) | (h) | (h) | (i) | 0.43 | 0.25 |
MECHANICAL REQUIREMENT | ||||||||
Tensile Requirements on Pipe body of welded pipes | Ratio | Elongation | CVN Absorbed Energy | Heat Treatment | ||||
Yield Strength (R10.5) | Tensile Strength (R) | R 10.5/ R | % | 0 degree celsius | ||||
PSI | Mpa | PSI | Mpa | Max | Minimum | Min J | Min ft. lb | Wield Seam Normalizing |
65,300-87,000 min | 450-600 min | 77,600-110,200 min | 535-760 min | 0.93 | 27 | 20 | ||
IMPACT TEST | |
AVG ABSORBED ENERGY | IND. ABSORBED ENERGY |
MIN (JOULES) | MIN (JOULES) |
27 | 20 |
API 5L X80 PSL2 LSAW Steel Pipes in Oman
Applicable codes and standards API 5L, 45th Edition / ISO 3183 Specification for line pipe – technical delivery conditions.
Nominal Pipe Size for
API 5L X80 PSL2 LSAW Steel Pipes: 2″ to 28″ O.D.
Wall Thickness – Schedule 10 through 160, STD, XS, XXS
Chemical Properties of API 5L X80 PSL2 LSAW Steel Pipes |
||||||||
Mass fraction, based upon heat and product analysis a | ||||||||
C | Si | Mn | P | S | V | Nb | Ti | Other |
max.b | max | max.b | max. | max. | max. | max. | max. | |
LSAW PIPE – API 5L X80 PSL2 | ||||||||
0.22 | 0.45 | 1.30 | 0.025 | 0.015 | 0.05 | 0.05 | 0.04 | g |
MECHANICAL REQUIREMENT | ||||||||||
Tensile Requirements on Pipe body of welded pipes | Ratio | Elongation | CVN Absorbed Energy | Heat Treatment | ||||||
Yield Strength (R10.5) | Tensile Strength (R) | R 10.5/ R | % | 0 degree celsius | ||||||
PSI | Mpa | PSI | Mpa | Max | Minimum | Min J | Min ft. lb | Wield Seam & HAZ Normalizing | ||
70,300-92,100 | 485-635 | 95000-125000 | 655-862 | 0.93 | 27 | 20 | ||||
IMPACT TEST | |
AVG ABSORBED ENERGY | IND. ABSORBED ENERGY |
MIN (JOULES) | MIN (JOULES) |
27 | 20 |
API 5L X70 PSL2 Pipe in Oman
Applicable codes and standards API 5L, 45th Edition / ISO 3183 Specification for line pipe – technical delivery conditions.
Size: ¼” to 36”
Wall Thickness: SCH 10 to 160, STD, XS, XXS
Length: up to 12 Meters
*Additional testing requirements met*: NACE MR
0175,NACE TM0177,NACE TM0284,HIC TEST, SSC TEST, H2 SERVICE,IBR, ECT in all
the products.
CHEMICAL COMPOSITION | ||||||||||
C | Si | MN | P | S | V | Nb | Ti | Other | Carbon Equivalent | |
Max (b) | Max | Max (b) | Max | Max | Max | Max | Max | % maximum | ||
CE(IIW) | CE(Pcm) | |||||||||
0.12 (e) | 0.45 (e) | 1.70 (e) | 0.025 | 0.015 | (h) | (h) | (h) | (i) | 0.43 | 0.25 |
MECHANICAL REQUIREMENT | ||||||||
Tensile Requirements on Pipe body of welded pipes | Ratio | Elongation | CVN Absorbed Energy | Heat Treatment | ||||
Yield Strength (R10.5) | Tensile Strength (R) | R 10.5/ R | % | 0 degree celsius | ||||
PSI | Mpa | PSI | Mpa | Max | Minimum | Min J | Min ft. lb | Wield Seam Normalizing |
70,300-92,100 min | 485-635 min | 82,700-110,200 min | 570-760 min | 0.93 | 27 | 20 | ||
IMPACT TEST | |
AVG ABSORBED ENERGY | IND. ABSORBED ENERGY |
MIN (JOULES) | MIN (JOULES) |
27 | 20 |
API 5L X80 PSL2 SEAMLESS STEEL PIPE in Oman
Applicable codes and standards API 5L, 45th Edition / ISO 3183 Specification for line pipe – technical delivery conditions.
Nominal Pipe Size for
Sizes : 2″ to 28″ O.D.
Wall Thickness – Schedule 10 through 160, STD, XS, XXS
API 5L X80 Specification
API 5L X80 Chemical Composition |
||||||||
Mass fraction, based upon heat and product analysis a | ||||||||
C | Si | Mn | P | S | V | Nb | Ti | Other |
max.b | max | max.b | max. | max. | max. | max. | max. | |
SEAMLESS PIPE – API 5L X80 PSL2 | ||||||||
0.22 | 0.45 | 1.30 | 0.025 | 0.015 | 0.05 | 0.05 | 0.04 | g |
X80 Steel Mechanical Properties | ||||||||||
Tensile Requirements on Pipe body of welded pipes | Ratio | Elongation | CVN Absorbed Energy | Heat Treatment | ||||||
Yield Strength (R10.5) | Tensile Strength (R) | R 10.5/ R | % | 0 degree celsius | ||||||
PSI | Mpa | PSI | Mpa | Max | Minimum | Min J | Min ft. lb | Wield Seam & HAZ Normalizing | ||
70,300-92,100 | 485-635 | 95000-125000 | 655-862 | 0.93 | 27 | 20 | ||||
Why purchase from Rexal Tubes?
Rexal Tubes is the leading manufacturer of pipes, tubes, fittings, and flanges. It has been operating in this domain for fifteen years and if one focuses on API 5L PSL1 Pipes, one can say that the company has the best of stocks and supplies. The variety is as diverse as it can get and one can select from a wide range of diameters, wall thickness, length, width, coating and various other dimensions. All these PSL1 pipes are manufactured using the most upgraded technology and the best of machinery. Our labs are completely in tune with the latest developments and always working with an innovative bent of mind.
Our technicians are skilled and ensure quality at every stage of manufacturing. The testing is also done in a foolproof manner so that the pipes come out with precise specifications. We also take responsibility for delivering the orders at the doorsteps of the customers without any delay or damage. Our huge stocks are always ready to meet any demands, be it regular, urgent or complex. We also offer customized offers to our clients and anyone looking for API 5L PSL1 Pipes can be sure of finding an ideal fit at Rexal Tubes. Cost-effective, competent and efficient, the pipes are tailor-made for the customers.
API 5L PSL1 Pipes Applications
API 5L PSL1 Pipes in Oman are used in oil, gas, petroleum and other industries for the transmission of oil, gas, and water. These pipes are strong and possess high resistance which makes them fit to be used in tough climatic conditions. They can withstand corrosive and non-corrosive environment as well. The steel pipes are corrosion proof and hence, suitable for such operations. They can also be put to use in other industries like water treatment, desalination, dairy, breweries, power plants, construction, ship building, etc.
The scope of commercial applications is quite varied as the API 5L PSL1 Pipes are generic in nature and since Rexal Tubes is all about customization, a customer gets a suitable deal without any trouble. The pipes are modified as per the special requirements of the customers and this is done keeping in mind the API standards and guidelines. At no point does quality take a backseat and therefore, one need not worry while ordering from Rexal Tubes. It is sure to fulfill the expectations of the customers.
Applicable codes and standards API 5L, 45th Edition / ISO 3183 Specification for line pipe – technical delivery conditions.
Size: ¼” to 36”
Wall Thickness: SCH 10 to 160, STD, XS, XXS
Length: up to 12 Meters
*Additional testing requirements met*: NACE MR
0175,NACE TM0177,NACE TM0284,HIC TEST, SSC TEST, H2 SERVICE,IBR, ECT in all
the products.
CHEMICAL COMPOSITION | ||||||||||
C | Si | MN | P | S | V | Nb | Ti | Other | Carbon Equivalent | |
Max (b) | Max | Max (b) | Max | Max | Max | Max | Max | % maximum | ||
CE(IIW) | CE(Pcm) | |||||||||
0.26 | – | 1.30 | 0.030 | 0.030 | (d) | (d) | (d) | (a) | – | – |
MECHANICAL REQUIREMENT | ||||||||
Tensile Requirements on Pipe body of welded pipes | Ratio | Elongation | CVN Absorbed Energy | Heat Treatment | ||||
Yield Strength (R10.5) | Tensile Strength (R) | R 10.5/ R | % | 0 degree celsius | ||||
PSI | Mpa | PSI | Mpa | Max | Minimum | Min J | Min ft. lb | Wield Seam Normalizing |
42,100 min | 290 min | 60,200 min | 415 min | – | – | – | ||
IMPACT TEST |
|
AVG ABSORBED ENERGY | IND. ABSORBED ENERGY |
MIN (JOULES) | MIN (JOULES) |
27 | 20 |
Notes:
- 0.50% maximum for copper; 0.50% maximum for nickel; 0.50% maximum for chromium and 0.15% maximum for molybdenum. For grades up to and including X52, Cu, Cr, and Ni shall not be added intentionally.
- For each reduction of 0.01% below the specified maximum concentration for carbon, an increase of 0.05% above the specified maximum concentration for manganese in permissible, up to a maximum of 1.65% for grades ≥ B, but ≤ X52; up to a maximum of 1.75% for grades > X52, but
- Unless otherwise agreed, the sum of the niobium and vanadium contents shall be ≤ 0.06%.
- The sum of the niobium, vanadium and titanium concentrations shall be ≤ 0.15%
- Unless otherwise agreed.
- Unless otherwise agreed, the sum of the niobium, vanadium and titanium concentrations shall be ≤ 0.15
- Unless otherwise agreed, the sum of the niobium and vanadium contents shall be ≤ 0.06%.
- The sum of the niobium, vanadium and titanium concentrations shall be ≤ 0.15%
- Unless otherwise agreed.
- Unless otherwise agreed, the sum of the niobium, vanadium and titanium concentrations shall be ≤ 0.15%
Other details
Surface
- All surfaces have been 100% visually inspected. The surface condition complies with API 5L standards.
- External surface of pipe shall be coated with a layer of varnish.
NDT
All pipes will be ultrasonic tested on pipe body and pipe end as per API 5L standards:
- longitudinal: 100% of the pipe surface
- pipe ends not scanned by automatic ultrasonic system shall be inspected by manual UT or Magnetic Particle Examination.
Certification and traceability
All dimensions will be supplied with a 3.2 certificate according to EN 10204, endorsed by recognized and independent inspection agency. Marking shall be in SI units (X42) accordance with API requirements & mill standard.
Dimensional control
All dimensions will be supplied according to API 5L clause 9.11; In addition, the following tolerances apply:
- Pipe body: +/- 0,75%
- Pipe end: +/- 0,5%
- Wall thickness: +15%, -12,5%
- Length: -0 / +100mm
Pipe Ends
Pipe Ends are bevelled. End angle shall be 30°- 0°/+5°, root face shall be 1.6mm +/- 0.8mm and fitted with bevel protectors.
Protection
Pipes are varnished on the outside.